Laying and maintenance tips
Technical features
STANDARD
ISO 10545/2
ISO 10545/3
ASTM C373
EN 101
ISO 10545/6
ISO 10545/9
ASTM C484
ISO 10545/12
ASTM C1026
ISO 10545/13
ASTM C650
ISO 10545/14
DIN 51130-04
DIN 51097
Pendulum BS
Pendulum AS/NZS
DCOF
LEED CERTIFICATION 4.1
ENVIRONMENTAL MANAGEMENT
SYSTEM ISO 14000 AND ISO 9001
VOC Emission
Declaration of Contents
EPD
SDS
BPD3
HPD
Packing
SIZE
BOLD 12,3·12,3
THIN 12,3·12,3
use
installation
recommended adhesive
mandatory joints
recommended fillers
cleaning at the end of installation
general cleaning
(installed tiles)
Colours
THIN
White
BOLD
White
Floor, wall – indoor, outdoor.
For an even, smooth shading effect when laying, alternate material from several different boxes
Adhesive for porcelain stoneware.
3 mm
Epoxy grout. Remove all traces of grout carefully before it dries completely.
CEMENT-BASED GROUT: Buffered acid (e.g. DETERDEK PRO by FILA, or similar). Wet the floor with water, dilute the product 1:5 with water
and pour it on the floor. Wait for 2 or 3 minutes then use a white scotch brite pad and rinse well with clean water.
EPOXY GROUT: Alkaline detergent (e.g. FILA CR10 by FILA). FILA CR10: apply pure, wait for 30 minutes then use a green scotch brite pad.
SILICONE: Solvent for silicone (e.g. FILA ZERO SIL.). Pour it straight onto the stain, wait for 20 minutes and remove the mark using
scotch brite.
PAINT: Can usually be removed using water, but if resin-based paints or particular enamels have been used, it is best to ask the manufacturer
which solvent is most suitable.
RUST: stain remover es. FILA NO RUST. Apply the product onto the stain, leave for 15 minutes, remove the residue and rinse thoroughly.
You are recommended to use ordinary neutral detergent diluted in water. Avoid using acid or alkaline products, waxes and/or impregnants.
During ordinary cleaning it is recommended to use extremely abrasive items (such as scourers and iron or steel sponges) as little as possible.
FEATURES
VALUE REQUIRED
SIZES
length and width
± 0,6%
thickness
± 5%
straigthness of edges
± 0,5%
wedging
± 0,6%
flatness
± 0,5%
water absorption
< 0,5%
< 0,5%
surface hardness (scala mohs)
>5
resistance to deep abrasion
<175 mm3
resistance to thermal shock
no visible alteration
no samples must show
frost resistance
no visible alteration
unaffected
resistance to chemical attacks
no visible alteration
FRINGE
visible defects
in conformity with standard
0,06%
0,06%
8
in conformity with standard
resistant
unaffected
resistant
unaffected
resistant
unaffected
5
R10
B
55 dry
40 wet
P4
0.51
20% recycled material
available upon request
available upon request
available upon request
available upon request
available upon request
available upon request
stains resistance
slip resistance
minimum 3
medium values
6÷10°
R9
10÷19°
R10
19÷27°
R11
27÷35°
R12
> 35°
R13
–
Anthracite
Grey
Rose
Red
Grey
Rose
Red
Anthracite
PCS·SQM
65,62
65,62
PCS·BOX
SQM·BOX
BOX·PAL
42
0,64
54
42
0,64
54
KG·BOX
17,15
16,50
KG·PAL
926,10
891
SQM·PAL
34,56
34,56
For information about the available grouts, please contact the customer’s care department: customerservice@mutina.it
464
FRINGE
FRINGE
465
