Laying and maintenance tips

Technical features

STANDARD

ISO 10545/2

ISO 10545/3

ISO 10545/6

ISO 10545/9

ASTM C484

ISO 10545/12

ISO 10545/13

ISO 10545/14

DIN 51130-04

DIN 51097

DCOF

Pendulum AS/NSZ 4586-13

EN 13501 (rev. 2005)

Leed 4.1

ISO 9001 – ISO 14001

Robinson Test

VOC Emission

Declaration of contents

EPD

SDS

BPD3

HPD

use

installation

recommended adhesive

recommended joints

recommended fillers

cleaning at the end

of installation

general cleaning

(installed tiles)

calibers (real size)

Colours

Gesso

Wall – indoor, outdoor.

Place the base of the chosen leveller under the flooring/tile and continue laying in sequence. Insert the tie rod in the threaded shaft and turn it

clockwise until the flooring/tile is level, using as little pressure as possible. When the adhesive/glue has solidified and the adhesion to floor is

sufficiently level: break the tie rod.

It is possible to use Class C2S2 cementitious adhesives to lay the slabs on substrates such as concrete, gypsum-based plaster (after applying a

primer) or cement, plasterboard or fibre-cement panels, and old ceramic tiles. Always apply a “double layer” or “full layer” of adhesive using

back buttering. Back buttering is, therefore, always recommended.

Apply the adhesive with back buttering, first on the back of the slab and then, on the substrate, taking care to cover the corners and edges,

avoiding any air pockets between the substrate and the slab. Spread the adhesive as required only on the surface where a slab is being laid

to prevent the surface from skinning over which stops it from adhering. It is recommended to use a 6 mm notched trowel for the substrate and

a 3 mm notched trowel for the back of the slab, taking care to spread the adhesive in the same direction, both on the slab and the substrate,

and to knock the surface with a rubber mallet, making sure any air pockets are eliminated.

2mm joints. Use wedges to fix the caliber differences in work size between tiles.

Cementitious grout / epoxy grout.

CEMENT-BASED GROUT: Buffered acid (e.g. DETERDEK PRO by FILA, or similar). Wet the floor with water, dilute the product 1:5 with water

and pour it on the floor. Wait for 2 or 3 minutes then use a white scotch brite pad and rinse well with clean water.

EPOXY GROUT: Alkaline detergent (e.g. FILA CR10 by FILA). FILA CR10: apply pure, wait for 30 minutes then use a green scotch brite pad.

SILICONE: Solvent for silicone (e.g. FILA ZERO SIL.). Pour it straight onto the stain, wait for 20 minutes and remove the mark using

scotch brite.

PAINT: Can usually be removed using water, but if resin-based paints or particular enamels have been used, it is best to ask the manufacturer

which solvent is most suitable.

RUST: stain remover es. FILA NO RUST. Apply the product onto the stain, leave for 15 minutes, remove the residue and rinse thoroughly.

You are recommended to use ordinary neutral detergent diluted in water. Avoid using acid or alkaline products, waxes and/or impregnants.

During ordinary cleaning it is recommended to use extremely abrasive items (such as scourers and iron or steel sponges) as little as possible.

This recommendation must be adhered to rigorously in the case of tiles with a glossy surface finishing as they are more susceptible to the risk

of scuffs, scratches and loss of shine, etc. In the event of heavy dirt or particularly textured surfaces, use an alkaline detergent and rinse after

washing. For large surfaces, the use of a floor washing machine is recommended. During every-day cleaning procedures, it is necessary to

remember that certain types of dirt (dust, sand) increase the abrasive effect of foot-traffic. Therefore we recommend that you avoid bringing in

this type of dirt, which comes in from the outside, by placing a door-mat at the entrance.

FEATURES

SIZES

lenght and width

thickness

straigthness of edges

wedging

flatness

water absorption

resistance to deep abrasion

resistance to thermal shock

frost resistance

resistance to chemical attacks

VALUE REQUIRED

DÉCHIRER XL

± 0,6%

± 5%

± 0,5%

± 0,5%

± 0,5%

< 0,5%

–

no visible alteration

no samples must show visible defects

in conformity with standard

in conformity with standard

–

resistant

unaffected

resistant

resistant

class 5

–

–

–

–

A2-s 1, d0

30% pre-consumer recycled

material

(Déchirer XL Gesso) 40% pre-

consumer recycled material

(Déchirer XL Grafite and Avana)

–

available upon request

available upon request

available upon request

available upon request

available upon request

available upon request

KG·PAL

SQM·PAL

492,00

60

no visible alteration

no visible alteration

stains resistance

slip resistance

class 3

–

–

–

–

1000mm x 3000mm

Grafite

Avana

V1

uniform variation

Packing

SIZE

100·300 cm

PCS·SQM

0,33

PCS·BOX

1

SQM·PC

3,00

PC·PAL

20

KG·PC

24,60

For information about the available grouts, please contact the sales department.

448

DÉCHIRER XL

DÉCHIRER XL

449