Technical features
STANDARD
ISO 10545/3
ISO 10545/4
ISO 10545/9
ISO 10545/12
ISO 10545/13
ISO 10545/14
DIN 51130-04
DIN 51097
DCOF
Pendulum AS/NSZ 4586-13
LEED CERTIFICATION 4.1
Robinson Test
VOC Emission
Declaration of Contents
EPD
SDS
BPD3
HPD
FEATURES
water absorption
breaking strenght
resistance to thermal shock
frost resistance
resistance to chemical attacks
VALUE REQUIRED
< 0,5%
Sp ≥ 7,5 min 1300 N
no visible alteration
no visible alteration
no visible alteration
TAPE
0,06%
resistant
resistant
resistant
resistant
5
R10
–
0,69
27 P2
20% recycled material
heavy use (zig zag half white)
available upon request
available upon request
available upon request
available upon request
available upon request
available upon request
Teknotessere
stains resistance
slip resistance
minimum 3
medium values
6÷10°
10÷19°
19÷27°
27÷35°
> 35°
–
> 0,42
Scan the QR code to
download the technical
features in other languages
collection
design
production
material
thickness
nominal sizes
specification
category
1·1 cm
3/8
”·
3/8
”
Teknotessere
Mutina Team, 2009
Artisanal
Homogeneous porcelain stoneware tesserae obtained by pressing and fixed on net
7 mm
1·1 cm (
3/8
”·
3/8
”) net 30·30 cm (12”·12”)
The collection is:
– 4 colours
Each element is pressed individually in special molds with more than one hundred element hole.
These tiles comply with the UGL Class Bla standard, suitable both for the residential market and for large-scale projects.
UNI EN 14411 App G (BIA group) UGL
on net 30·30 cm
12”·12”
R9
R10
R11
R12
R13
Laying and maintenance tips
V2
minimum variation
use
installation
recommended adhesive
recommended joints
recommended fillers
cleaning at the end
of installation
general cleaning
(installed tiles)
calibers (real size)
Floor, wall – indoor, outdoor.
Lay on perfectly flat, dry walls.
NON-RAPID-DRYING adhesive for porcelain stoneware to make it easier to fix the sheets.
Place the sheets with the same joint as within the sheet.
Cement-based grout / epoxy grout.
Remove all traces of grout carefully before it dries completely.
CEMENT-BASED GROUT: Buffered acid (e.g. DETERDEK PRO by FILA, or similar). Wet the floor with water, dilute the product 1:5 with water
and pour it on the floor. Wait for 2 or 3 minutes then use a white scotch brite pad and rinse well with clean water.
EPOXY GROUT: Alkaline detergent (e.g. FILA CR10 by FILA). FILA CR10: apply pure, wait for 30 minutes then use a green scotch brite pad.
SILICONE: Solvent for silicone (e.g. FILA ZERO SIL.). Pour it straight onto the stain, wait for 20 minutes and remove the mark using
scotch brite.
PAINT: Can usually be removed using water, but if resin-based paints or particular enamels have been used, it is best to ask the manufacturer
which solvent is most suitable.
RUST: stain remover es. FILA NO RUST. Apply the product onto the stain, leave for 15 minutes, remove the residue and rinse thoroughly.
You are recommended to use ordinary neutral detergent diluted in water. Avoid using acid or alkaline products, waxes and/or impregnants.
During ordinary cleaning it is recommended to use extremely abrasive items (such as scourers and iron or steel sponges) as little as possible.
This recommendation must be adhered to rigorously in the case of tiles with a glossy surface finishing as they are more susceptible to the risk
of scuffs, scratches and loss of shine, etc. In the event of heavy dirt or particularly textured surfaces, use an alkaline detergent and rinse after
washing. For large surfaces, the use of a floor washing machine is recommended. During every-day cleaning procedures, it is necessary to
remember that certain types of dirt (dust, sand) increase the abrasive effect of foot-traffic. Therefore we recommend that you avoid bringing in
this type of dirt, which comes in from the outside, by placing a door-mat at the entrance.
–
Packing
SIZE
20,5·20,5 cm
PCS·SQM
23,88
PCS·BOX
16
SQM·BOX
0,67
BOX·PAL
96
KG·BOX
14,20
KG·PAL
1363,20
SQM·PAL
64,32
514
TAPE
TEKNOTESSERE
515
